Showing posts with label out. Show all posts
Showing posts with label out. Show all posts

The need of keeping water out of the bilge of a metal boat

Sunday, March 27, 2016

I always start my surveys on metal boats by using Thermal Imaging of the hull. This helps me locate the structural components of the metal boat. I am also looking for trapped moisture and/or water. If this is found, then there is a good chance there will be corrosion. Next I conduct an inspection of the bilge of the boat, including, anchor, sail, cockpit lockers, and lazarettes. Now I have a very good idea where to concentrate my UTM-audio gauge. I take readings of the whole hull, but will do more readings in the areas of concern.

When I see water in a bilge of a metal boat beyond what might be in a sump I get concerned. I would like to see dry bilges on all metal boats, but this is not always possible. On Tuesday I surveyed a steel trawler. Overall this boat looked to be in fair condition, but then I saw the water in the bilge, a lot of it! There was heavy scale in some areas because of the standing water.  I knew this was an area I needed to spend some time getting thickness readings.

The next day I did my audio gauge. My readings indicated plate wastage. In some areas I could not get a reading that most likely is caused by heavy scale. My visual inspection from inside confirmed the heavy scale. When I arrived at the boat I noticed some weeping from what I hoped was paint blisters. Then an hour later water stared streaming from one of the blisters. Just to think only the paint was holding this section of plate together.

The good news! The boat was out of the water it will not sink. Steel boats can fixed; by cropping out the bad plate and adding new. In a short period of time, she will be underway again.

The moral of this story? If you own a metal boat keep an eye on the bilges.

I will post photos in my next post.
Read More..

how to build a boat out of wood

Thursday, March 17, 2016

how to build a boat out of wood
To build a wooden boat you will want wooden cedar plank. Now, the length of the boards will depend on exactly what wood you happen to be using. If you might be using cypress wooden then you will have eight various dimensions based on which you will need to shape your planks.



Many of these eight types of planks will probably be required for constructing the fishing boat. However, should you be building the actual boat beyond oak next there will be concerning six various kinds of plank needs. If, Ga pine and then three varieties while whether it is white this tree then it will likely be just one dimensions and several planks of the same sizing.



Now, if you are building a travel boat and then obviously youll build a single with a toned bottom. Exactly how to make a fishing boat and then you understand that the most important thing to be aware of during this sort of boat building is the originate. No matter what an individual build your motorboat out of, your stem must be of good bright oak. Youll need the sideboards, 2 in range. Saw all of them properly and after that plane all of them.



Now increase the risk for mould which may be made of aged material in addition. Leave a few space to the stringers and make the actual stern panel next. Next is ready, toenail up the sideboards for the stem which has a hammer ensuring that you claw then in a very double line. Now you can placed in the fits. While accomplishing this keep in mind that the actual moulds must be perpendicular for the boats heart. Fasten all of the moulds and also the transom and then utilize galvanized claws that are employed for permanent nailing of the boat.





Now its time to wear the bottom. Try this by converting the fishing boat upside down then nail the bottom with the sideboard combined with stringer. Make sure that there is absolutely no caulking; for this you should make the mutual between the watercraft as restricted as you can. Today, turn it above on their bottom and have the seating placement. The actual seats must strictly be manufactured of cypress since then they will likely be pretty comfy. Then whatever you have to do will be cut slot machine games, two, out of the centreboard. After this you must fasten a couple of posts from these factors.



Now you have in order to nail inside keel and the ground firmly to ensure that no problem occurs. Today place the cross-bow supports of the terrace, curving these people as you accomplish. Now while everything is carried out you should get the actual cockpit set si how the combing can happen. After you do that, get ready for the actual canvas terrace. Paint together with thick color, white colored. More or less next, your vessel structure is created. You will only ought to place the oars and further material becoming a complete vessel. This is hence the basic of methods to make a motorboat, one which can be a wooden breeze boat.


Ultimately you must remember in which decent vessel design computer software helps you to develop the vessel of your dreams. Most likely the best thought is to get some form of 3D motorboat design application that is reasonably priced, easy and accommodating to use and is also suitable for any person from the novice model vessel builder for you to professional muscle size ship companies.

To see a lot of the latest and greatest Animations Boat Layout / Computer design Ship Private yacht and Fishing boat Design Application visit our own review web page here: Top quality Boat Design and style Software.

Relax knowing, I have attempted 3D Fishing boat Design and may personally advise this product.

Coming from my evaluation I have found in which 3D fishing boat Design is simple to use, extremely flexible which is everything you need to design and style a boat, luxury boat or vessel.

This is an remarkable piece of software in a bargain price, you cant lose.
Read More..

Boat Out Of Wood

Sunday, March 13, 2016

Build A Boat Out Of Wood

Master Boat Builder with 31 Years of Experience Finally Releases Archive Of 518 Illustrated, Step-By-Step Boat Plans.
The Easilet Wat To Build Your Boat!

Build A Boat Out Of Wood
The Easilet Wat To Build Your Boat!

Build A Boat Out Of Wood

If you are here to looking about Build A Boat Out Of Wood, You have come to the better place. After tons of study of the Master Boat Builder with 31 Years of Experience Finally Releases Archive Of 518 Illustrated, Step-By-Step Boat Plans., We have come up with the The Easilet Wat To Build Your Boat! goods.

Build A Boat Out Of Wood : Drift Boat Building Kits How To Build A Boat Propeller Model Boat Plans Balsa Instructions On How To Build A Wooden Boat Free Grp Boat Plans 10 Foot Plywood Boat Plans Plywood Race Boat Plans Hartley Boat Plans How To Build A Boat Dolly Plywood Boat Building Videos Wooden Boat Building For Beginners Boat Building Plans Grand Banks Dory Free Boat Plans Catamaran Aluminum Fishing Boat Building Kits Dn Ice Boat Plans Free Wooden Boat Building Tools Uk Build A Boat Diy How Do You Build The Boat On Club Penguin Model Boat Stand Plans 12 Foot Aluminum Boat Plans Aluminum Swamp Boat Plans How To Make A Wood Boat Toy How To Build Wooden Jon Boat Easy To Build Wooden Boat Plans Boat Building Regulations Australia How To Build A Boat Using Household Items Boat Building Yards Australia Wooden Boat Building Vancouver Boat Building Workshop Aluminium Boat Building Kits Plywood dragon boat plans Make A Wooden Model Boat Aluminum Fishing Boat Building Plans Model Boat Plans Nz Small Cat Boat Plans Small Bass Boat Plans How To Build A Boat Port Molded Plywood Boat Building How To Build A Boat Of Cardboard Wooden Boat Glossary Small Boat Design Plans Wooden Boat Building Supplies Uk Fishing Boat Deck Plans Wooden Boat Building Forum Australia Boat Building In Your Own Backyard Boat Plans Bolger Small Runabout Boat Plans Runabout Boat Building Plans Learn How To Build A Wooden Boat Plans For Building A Pontoon Boat Boat Plans Popular Mechanics Aerokits Model Boat Plans Plywood Boat Plans The World Standard Wooden Jon Boat Kits Wooden Boat Kit Plans Building A Lapstrake Wooden Boat Wooden Boat Show Boat Garage Plans Build A Boat Malibu Whitehall Rowing Boat Plans Easy Build Boat Plans How To Make An Easy Wooden Boat Plywood Motor Boat Plans Build Your Own Aluminum Boat Plans Adirondack Guide Boat Plans Free How To Make A Wood Speed Boat Jaws Orca Model Boat Plans Fiberglass Boat Building Plans Free Model Yacht Boat Plans Kids Rowboat Plans Boat Building Process Marine Plywood Boat Building Wooden Row Boat Building Plans Build A Boat Team Building Duck Boat Blind Plans Build A Boat Out Of Wood.

The Easilet Wat To Build Your Boat! for Build A Boat Out Of Wood


The Easilet Wat To Build Your Boat!
Master Boat Builder with 31 Years of Experience Finally Releases Archive Of 518 Illustrated, Step-By-Step Boat Plans.

The Easilet Wat To Build Your Boat! Aluminum Jet Boat Plans Design Wooden Dories Boat Plan Sea Queen Model Boat Plans 12 Wooden Boat Plans Free Easy Build Boat Plans Rowing Boat Plans Free Wooden Boat Underwater Primer Plans For Building A Jon Boat Boat Building United States Wood Epoxy Boat Plans Wooden Boat Plans Sailboats Build A Bait Boat Plans How To Make A Wooden Steam Boat Free Plywood Drift Boat Plans How To Build A Boat With Popsicle Sticks Wood Boat Bookshelf Plans Boat Building Degree Boat Ramp Plans Aluminum Drift Boat Plans Rc Model Power Boat Plans Free Wooden Boat Plans Uk Build A Wooden Motor Boat How To Build A Boat Trailer Australia Wooden Boat Plans Rowing How Do U Build A Paper Boat Boat Building Wood For Sale Model Viking Boat Plans Build Wooden Boat Kit Wooden Power Boat Plans How To Build A Kite Boat Build A Boat Out Of Wood.

How do Build A Boat Out Of Wood.
Does a Build A Boat Out Of Wood.
Is my Build A Boat Out Of Wood.
Can Build A Boat Out Of Wood.
When Build A Boat Out Of Wood.
Why the Build A Boat Out Of Wood.


The Easilet Wat To Build Your Boat! : Master Boat Builder with 31 Years of Experience Finally Releases Archive Of 518 Illustrated, Step-By-Step Boat Plans.

Read more for Build A Boat Out Of Wood : Boat Building In Ancient Egypt,Wooden Boat Building Au,Boat Building Uk Jobs,Wooden Boat Building Gabriola Island,Fishing Row Boat Plans,Build A Boat Out Of Wood


Read More..

Four More Great Sails Round Out July And A Serious Health Issue Changes Plans for August

Tuesday, February 16, 2016

Four more day sails and one work day closed out July. Regrettably, Lene was not aboard. Average of 4.55 hours per sail.
First was Greg and Kathy. Greg is a member of my Mens Book Group. We men get to meet each others wives when we have dinners at each others homes and at our annual Spring social. Kathy and Greg have also visited the Barnes Collection in Philly with us a couple of years ago. Greg, a terrific artist and retired professor of drawing has sailed with me several times and Kathy, a retired teacher,
Gregs drawing, sorry about side view.
overcame her fears on this rookie voyage. The wind started at less than ten and grew to more than 15 as the day wore on. We used the small jib and main, getting to Sea Cliff YC and then dipping into Manhassett Bay far enough to see Port Washington, on the way home. Pinot Grigio on the mooring at the end. We have been enjoying stronger than normal winds this July.
Next up was Cynthia, a past guest, in a lot of wind for 2.25 hours underway. We used reefed main and no head sail and made speeds of five to seven knots on beamy reaches back and forth into Little Neck Bay.
The excitement came at the end, when it was time to fetch the mooring. This is no task for a sweet petite lady who is a bit older than I. So I had to try to get close to the pickup stick and slow ILENE before running forward to the bow to grab the bobbing pickup stick and then pull up and grab and attach the bridle before the wind blew us away. I made six tries. The problem is that when you slow down enough to not race past the mark, even though you aim as close to the wind as possible, the wind will come a few degrees on one side or the other and blow the boats bow away. I gained a new appreciation for the accomplishments of my friend Jim, who sailed "Aria" solo for many years, though his run from tiller to bow, on a 26 foot boat, was shorter than mine. Twice I grabbed the pickup stick in these six tries. The first time the boat turned and the wind pushing on its side made the boat too heavy for me to hold; I had to let go. Frustration!!!! The second time the cheap flimsy line with which the mooring servicer had tied the pickup stick to the bridle -- parted! I had the stick but it was no longer attached to a bridle. FRUSTRATION! And in all this I had a few close encounters with friends moored boats -- but no touches. Strong reverse gear pulled ILENEs bow back past the bow of the neighboring boat. So what to do? Call the Harlem launch and ask for help! The operator wisely let me wait, circling, for a few minutes while he got reinforcements. Two strong men Dave and Jeep, jumped from the slow moving launch to the slow moving ILENE. Then, when I got ILENEs bow to the mooring ball, and held her there, they used a boat hook to grab the bridle and the problem was solved. The alternative plan B I had contemplated would have been to go a bit outside of the mooring field and drop anchor. Cynthia professed that she was never worried. This was because I never showed my fear. Lene joined Cynthia and me for dinner at Neptune Restaurant, a favorite, on First avenue near 12th Street.
Next I enjoyed a very productive work day with Lenes cousins sons, Jake and Jared. They were transformed from guests the weekend before, to worker bees, for five hours. The economy is so weak that they dont have summer jobs. So they liked the money and I liked the quality and quantity of the work they accomplished, largely helping me bring the RIB dink from the upstairs locker to the dock and compounding and waxing the topsides and cockpit. While they worked I varnished the other side of  the cafe doors, replaced the mooring bridle to pickup stick line with a stouter one, whipped a few ends and cleaned up the galley stove top. I also picked up the outboard from Tony, proprietor of Island Outboard, two blocks from the Club, on City Island Avenue (718) 885-2012. Tony has done a lot of good work on my outboard over the years and we use it many times more than most people.
Next day being a Wednesday, I tried to revive the Club within a Club (See Blog, July 2012.) This is the informal group of people who have Wednesday afternoons available. With the loss last year of four of our larger boats (ILENE was in Maine), the group had sort of fizzled out. But on only 15 hours notice only three other folks showed up. The very light winds may have held down attendance as well and I have been encouraged to try artificial respiration again later, with more notice. Morty asked that we sail with him and his wife Clara on their 30 foot Catalina, "Easy Living." Completing our quartet was a new member, Mary, an Oncological Nurse Practitioner, who does not have a boat yet but has been found qualified to use the Clubs J-24s and is enthusiastic.  The sailing was rather listless with very light wind but we did get up to 4.5 knots on two occasions when puffs lifted us. And the lunch before hand, the conversation during and the G&T (vodka actually) after were all quite good.
Finally, on the last day of the month, I helped set up a sail with our former member, Nick, whose boat we helped sell last year after he became a resident of the Hebrew Home for the Aged due to memory issues.
Master carpenter and dance instructor, Nick, at dinner after.
I signed him out and was met at the Club by three other old friends of his, one of whom, John, had driven up from Marylands Eastern Shore.
Don and John
We were off the mooring for five hours: close hauled out of Eastchester Bay, then broad reaching with a couple of jibes to about six miles east of Matinecock Point before tacking for one long  close reach back past Execution Rocks. Then to give them some excitement, after changing back from the genoa to the small jib, we tacked back up through Hart Island Sound, over to near L.I. and then to the mooring. After dousing sails we passed through the channel behind Big Tom under motor and went through the City Island YC fleet looking for Nicks old boat but we did not spot her. All of these men are good sailors. Like Nick, Don and John are past members of the Harlem. Nick taught John how to sail. Don preferred to trim sails and the other three men shared the helm. Nicks memory problems definitely did not involve any impairment of his ability of to handle the helm.  Pat, rounded out our group.
Co-organizer of the event, a nurse, and one of the most knowledgeable and helpful men in the Club.
He spotted a damaged ring clip at the tack of the jib,which we replaced and taped. It was catching the Genoa jib sheets, causing damage to them and itself. I usually try to "improve" my friends boat when I sail with them. This time Pat did this for me. He had also brought the Chardonnay that we shared in the cockpit, apres sail. Then the guys helped my try to inflate the dink on the dock noting that the washer at the end of the pump hose was missing, which was the problem. (A new one is on order.) The day ended with dinner together before the three others drove Nick home.
And proving that our rosy life does not exist without a few thorns, I got a call from Lene during our dinner. The needle biopsy of her left lung came back as malignant, but stage one, slow growing and small. It gives one cause to pause. It will be removed by laperoscopic surgery on August 12, with preparatory tests between now and then. If one has to catch cancer, this is the type to get and the early dtection was quite lucky.
But, of course,  this means that our plans to cruise up to Nantucket during the entire month of August will not come off. We are now planning a short five day cruise in the Sound before the surgery, during which we hope to catch up with the HYC Club Cruise, at Matinecock, in the Sound. Lenes attitude is really great. She is cheerful, positive, determined and optimistic. She knows that worry does one no good. NYUs Langone Medical Center is a world class hospital and she has excellent doctors. Stay tuned!
Read More..

Ralph helps out with some laminating

Friday, February 12, 2016

My old Boss (from my Austrade days) in our basement workshop, wielding the wooden mallet we use to straighten bits of wood that were laminating.  Here laminating the cleats for the web frames.  Ralph and his wife Maria are with us from their home in Sydney, on their way to Denmark.  Here they are with us yesterday on our boat Xena.

Read More..

Fitting Out A Newly Built Boat

Tuesday, February 2, 2016

Fitting out a new boat can be difficult and very very expensive.I have known people to buy $20,000 boats and then drop another $50,000 to $60,000 on refits before they even touch water.Well my boat will cost around $3500 for the completed bare hull and cabin. See my post "Spira International 27 Foot Boat Plans Build Costs".Im looking at another $2,000 for paint,finish,and interior,and roughly $2,000 for powering the boat.So what about electronics.This is a difficult one to put a price on.The one system that you want to be all new is the waste,water, and plumbing system.This could give you tainted water,flood your boat, and/or make it stink like a sewer,if old equipment is used.Pumps maybe ok with a good cleaning,but tanks and piping need to be all new.

Understanding Boat Plumbing and Water Systems

First,how will the boat be used?For the first two or three years,the boat will be trailered to lakes and coastal areas.Eventually,it will be used to do "The Great Loop Cruise". Knowing how I will use the boat and when I may need to make upgrades helps a lot.I can resell my old equipment, when I upgrade, to recoup some cost.To do this, I will have to buy decent quality reliable products and maintain them in as new condition as possible.Ive rarely ever had problems taking care of things.

 The Great Circle Route

Second thing,the power plant.Jeff Spira,the designer of my boat, recommends an outboard for power.I have some issues that make outboards a bit of a challenge to use as a means of propulsion.My area has a strict ban on two stroke outboards.That leaves me trying to find a four stroke with controls and gauges.Four strokes are a relatively new thing and used set ups are still fetching top dollar.I cant afford to pay around $10,000 for a 90 horsepower four stroke outboard set up.After consulting with Jeff Spira,he has approved the use of a sterndrive.These are plentiful in my area and cheap,relatively speaking.A good complete four cylinder 140 horsepower 3.0L Mercruise set up goes for between $1500 and $3000.

Third thing,I have a plan to cut costs,get most of the stuff I need,and possibly make a little money back.I will buy a donor boat that is complete and running good.I can find sterndrive boats in good operating condition between $1000 and $6000.Some even have twin sterndrives.That would give me a few options.1)Sell the extra sterndrive set up. 2)Keep the extra sterndrive set up as a back up. 3)Clean up both sterndrive set ups,sell them,and buy a completely new set up.My choice would be the 140 horsepower diesel Volvo Penta D3-140 sterndrive set up.These are hard to find on the used market and most are damaged.New they start out around $12,000.A new 3.0L Mercruise sterndrive set up runs $6000 to $8000.On rare occasions,they can be had for around $5000 to $5500,but come with a catch.They must be set up by a factory Mercruise service center.

Stern Drive Manuals

The donor boat.This is tricky depending on location or region.Most boats here are bow riders or water sport boats.All tho,its not unusual to find cuddy or cabin cruisers for really good prices.Beware that a lot of boats are not properly maintained, and thats the reason they are for sell.Of course, one can get lucky at times and buy a boat that barely needs anything to be back on the water.Look for soft spots in the transom and floor.If they are soft then the stringers and flotation foam have been compromised,and the boats structure has been compromised.This is a good negotiating point.It is really expensive and labor intensive prospect to gut a hull for transom and stringer replacement.

What can be used from the donor boat?This depends on what boat is decided on to be the donor.When building a boat you need everything.

Heres what I look for in a donor.
Power Plant-must be running with all controls and gauges.
Electronics-VHF,depth sounder,radar,gps,etc... in operating conditon.
Pumps-Wash down,bilge,fresh water,black water,and grey water.
Electrical-Batteries,inverter,charger,genset,breaker panel,fuse panel,switches.
Windows-I plan to build my own to fit my boats design.
Bimini Top and canvas-It wont fit the boat,but it can be modified and save some money.Resell is an option.
Interior-Its hard to reuse interiors but they can be modified to work.
Thru Hulls-Pure preference,but I want bronze if theyre under water,and stainless steel above water.Plastic ones crack and fail.
Anchor,Rode,Bow Pulpit,and Windlass-These can usually be modified to work.
Heads(Toilet)-These things are a pain,save yourself the headache,buy new.
Sinks,Faucets,Showers-If these are in good condition,I will use them.I prefer stainless steel.
Tanks and Plumbing-All new.This was discussed earlier in this post.
Cabinets-These can be modified to work.
Hatches and Vents-These can usually be reused as is.
Swim Platforms and Ladders-Modified they can work.New they are outrageously priced.
Air condition unit(s)-These can be reused without much change.Good insulation can help keep the cool in.
Heaters-These can be reused without much change.


There is other items that can be reused but this is the most common expensive items.Anything that isnt used can fetch good money on Ebay or Craigs list.

RVs,motor homes,travel trailers can provide some good stuff also.I wouldnt use parts from them on a full time cruiser.A weekend cruiser should be fine.However,nothing will be USCG or AYBC approved.

Boat Systems Handbook

Read More..