March 18 20 Three Lay Days in Lake Boca Zero Miles

Lake Boca is a large rectangle of water cut into the west side of the beach strip of Boca Raton, from the Boca Inlet north for about  .4 miles, along the east side of the ICW, .2 miles wide. The center of it is very shallow with only the edges navigable for keel boats. Anchorage for sailboats is in the NE corner. Access to land is in a park with a boat ramp and dinghy dock on the west side of the ICW, just south of the Palmetto Park Boulevard Bridge, north of the lake (less than half a mile away). We will have to request an opening of that bridge when we leave to head north.

Craig had a better idea about where to go ashore, because the tide runs fast under the bridge and big boats go too fast and make wakes: his boat, Sangaris, pictured above, is docked in a canal at the back yard of a private home about a mile further north. He picked us up there and we got to see Sangaris again, after all her European adventures.

Ive been saying that when I get too old to sail ILENE, a radio controlled sailing boat on a lake may be in my future. Well Kathy had to work, Lene did her phone work from Kathy and Craigs house, and Craig took me to another gated community a bit further north called Kings Point, which has a lake in which his club races such boats. Beauties, one meter long, high aspect ratio,with 3/4 of the weight in the keel. The control box is worn on a strap around ones neck and the right thumb controls the rudder by pushing its joy stick left of right, while the left thumb controls both sails with back to pull them closer hauled and forward letting them fly for the downwind legs of the course. Below is Craig, demonstrating and Erwin, also a Past Commodore of the Harlem and racer, to the right.

All I can say is that it is a lot harder than it looks and I lost every race; actually I did not finish them. When aboard a boat you can easily see if your bow is pointed to the right or left of a buoy; you feel the tension of the water on the rudder; you can see how close to the wind you are. But offset by 50 to 100 yards and at a strange angle, these critical facts are not readily apparent at least not yet, to me. And rudder control is maintained by constant pressure of perhaps a half inch on the "tiller". But these things can be learned and the fifteen guys had a good camraderie going. Kathy is one of the guys and quite competitive when she is not working. I raced her boat, number 3. Erwin brought some beer for the "after". We plan to see Erwin again before heading north.

And in the evening we had dinner with not just Craig and Kathy, but also Mike and Janet. The latter have a Florida home and we will see them again at their home in St. Michaels, off the Chesapeake on Marylands Eastern Shore, on our way home. I forget to take their picture but they are pictured from when we visited them in the Chesapeake in 2012 if you want to take a look. A nice Greek restaurant.

We rented a car for one day for trips to cousin Naomi to pick up a late arriving bundle of mail from home, the pet food store, Publix, the automotive store for things for the dink, the post office, the bank and the beach.

On our last day we toured around Mizener Village, which is a ritzy shopping mall. I got some new shorts because none of my old ones are unstained. We had lunch out and saw The Second Best Exotic Marigold Hotel, which celebrates India and aging. Good but not as good as the first movie. The theater is called Ipic and does not really want to be in the movie business. Seats are very large and comfortable and $14 if you want to sit in the first two rows, or $24 if you want even more luxurious seats with free use of a pillow and blanket and free popcorn. And Ipic has a full service restaurant and bar that you can patronize before or after and provides delivery of food and drink to your seat during the movie. And no reduced rate for matinees or for seniors.  The staff said it is a "good place to impress your date on a special occasion". The film is apparently just a gimmick to get folks to come in and spend money on the "entertainment experience package". This hustle offends me and I hope it fails, though we were the only two in the sixteen "cheap" seats while perhaps ten people sat behind us. We have had nice warm dry calm weather while in Boca. Next stop: Palm Beach.

Read More..

Boat Building School

Boatbuilding photo The key fruit to deciding which socio-economic class C. How to choose the best boatbuilding course for you. View Details For This School The Bayfront Maritime Centers waterfront campus adeptness inwards Erie Pennsylvania. This one hundred fifty paginate Word with its long hundred photographs and drawing details how you can build light beautiful shin on frame boats. Located Hoosier State historic downtown Wilmington North Carolina along the Cape F boat building school.

H Photograph away Roger McKee. The Landing civilize is a full phase of the moon meter licenced send secondary coil train that provides education in modern yacht design boat building and devil dog systems. Bayfront Maritime Center Wooden Boat Building. Best suits your needs is to carefully read each course. Learn the finest & most efficient forms of traditional wooden boatbuilding developed in the early 1900s by Puget Sounds master boatbuilders & shipwrights. Commission affirmation A non profit educational centre that seeks to provide quality traditional and composite wooden boat building skills to preserve and continue boat building school.

Read More..

wooden boat builder

wooden boat builder

Very good wooden boat building ideas as well as study materials are the initial a couple of things you have to try to find at the start of assembling your shed. A beginner motorboat designer offers a number of confusions at the outset of your venture. The place to start? How to start via? A good veteran motorboat contractor begins getting plenty of confusions on the in depth stage during the particular venture. The one treatment for these issues are perfect wooden boat building ideas and also study materials. An advanced beginner motorboat contractor, you might want to produce a easy and simple to develop to be able to vessel. The very first choice which will come for you to my personal uncover to suit your needs is seeking stitch and glue boat plans. Creating this sort of watercraft requires subscribing to plyboard cells regarding preferred form collectively employing adhesive as well as appropriate additional parts. You can create this sort of fishing boats per day. Nevertheless, setting up a prepare for these watercraft is nothing a lot more included. As an example joint parts of which fishing boats have become important from your viewpoint associated with architectural power. A fantastic insurance policy for this kind of watercraft really should have a really in depth attracting and also points of the joint parts and all sorts of the rest. Like a experienced fishing boat contractor, you might invest in a top rated hydroplane. Look at the degree of specifics essential right now there * form, dimensions, area involving engine things are all planning to possess outcomes on the velocity and more importantly about protection if the fishing boat works at the rate involving 58 miles-per-hour. If you are a novice or perhaps skilled, regardless of whether you need to produce a paddling, canoe or perhaps hydroplane, great wooden boat building ideas as well as handbook are the very first pair of demands.

Read More..

Rc Boat Plans For Download Reserve Your Spot By Clicking The Order Button Below And Get Instant Access To Over 518 Boat Plans Join us

---

Boat Rental Paris Is very Present With Appreciate Paris, France Attractiveness

Regional rental houseboats as well as neighborhood leasing host appropriate after number have turn out to be high on the distinct interest within the visitors and furthermore citizens. People seek the solutions of the majority of these houseboats by way of which they are capable to advantage from because of their family members as well as friends appeal of loading h2o in addition to appealing landscape. The majority of these neighborhood regional rental dwelling watercraft, raft soon after quantity as well as watercraft are typically affecting international areas as well as cities on the economic institution with regards to numerous channels. Boats employ, as well.

As renting houseboat in paris are a fantastic company presently and it is also obtaining a great deal in the vacationers attraction. A great deal of folks use simple Paris boat for fishing along with other company activities like travel involving further goods such as each and every single day employ around the water. Boat rental Paris is really frequent folks retain the solutions of empty motorboats to relish themselves in addition to further organization functions. Lots of firm men use these sorts of fishing boats with no personnel together with exclusive private yacht. Theyve got their very own crew to generate their certain visit cheaper. Raft following raft will be the nicely toned fishing boats for sale which in turn drift when youre receiving began related with drinking water. Barge rental Paris could be regarding superb significance to be able to exceptional and business capabilities men and women use them industrial producing financial organizations, dining establishments, coffee shops, booksellers, locations and also other public venues for you personally to snare tourists attractiveness. Lake Seine is complete of beautiful landscapes along with peaceful water. Rome is genuinely a great location, town packed with bulbs and sophisticated style together with River Seine functions a lot more a whole lot a lot more enthrallment to its elegance.

House rent a houseboat or barge in paris is usually a vessel that have been meant to provide man active. It is a fantastic organization these days as well as some folks retain the solutions of this distinct boat to relish their specific breaks. Such nearby on the inside Greater london are offered about economical charges normally any houseboat for six individuals possessing area of 550 to ensure that it is possible to Six hundred also as 50 Sq. ft. might be purchased $250 for you personally to Dollars Greater than 200 for every single Saturday and Sunday with each other with $2500 in order that you can Dollar 4 thousand monthly. Nearby hire houseboats distant moreover get recognition. Your own personal renting home fishing boats around the inside Paris, Portugal has been applied offered that historic reenactments with each other with ceremony. These kinds of houseboats are supplied also far associated using the the European union and have presented a classy plan to women and men moving into folks areas.

The organization enterprise associated with neighborhood leasing fishing boats, boats plus house watercraft in the capital represents crucial execute inside the financial development and improvement of the us, Britain. This is why govt is actually going to help to produce laws for utilizing night work for the duration of these types of attributes of men and women.

Read More..

Build Boats With Wooden Boat Plans

build wooden boat

build wooden boat can be an enjoyable pastime for people who like working with their hands. Its not only entertaining, but finished projects can also be useful when going on a vacation. In fact, some people will even build these crafts, not only for their own use, but for sale making the hobby not only fun but also profitable.

For those who are thinking about starting the activity, heres how to start making your wooden boat.

Purchase a Kit

Wooden boat blueprints kits are found with some searching. The kits only include fasteners, epoxy, sails, rigging, etc. Purchasing the kits will definitely save time and is an excellent way to start on this hobby. Otherwise, you must purchase ease different hardware required separately after you track it down or have it special ordered.

build wooden boat

build wooden boat

Start Building

Make sure all the materials are present before actually starting to build. Ready a clean space for this stage, preferably somewhere with lots of light. Dont forget to carefully study the wooden boat blueprints provided in the kit in order to determine exactly how the boat would look when finished.

Dont Rush

If theres something that just doesnt seem to go with the structure, then dont force it. Put the materials down and mull it over or perhaps take a break to give the mind a time to adjust. Most of the new hobbyists try to speed the process up which could only result to failure in the end. Instead, choose quality over quantity and enjoy the boatmaking process. If possible, try to stretch the activity to cover a few hours every day for as long as possible, depending on the complexity of the design.

Most people who have been in this hobby for a long time no longer use boat kits when creating. All they do is purchase wooden boat plans and use raw materials in creating the figure. This not only lengthens the time in creating the boat but also draws out the pleasure in working with ones hands. Plus, this also gives hobbyists the option to make changes in the make of the design, letting them add or remove a few items to suit their purpose.

Although it may look laborious at first, creating a wooden craft from scratch provides a very fulfilling feeling in the end. As a hobby, it is an excellent way to get ones mind off stressful thoughts and concentrate on something constructive.

Read More..

October 25 Portsmouth VA to Elizabeth City NC 43 8 Nautical Miles

Today we traversed the Great Dismal Swamp, one of three inland routes between Norfolk and North Carolina. This is the westernmost route and most of it is a very straight and narrow (about 50 feetwide) canal

that is not very deep (about eight to ten feet).A new route to a new port.
One thing about it is easier. Normally I piece together many legs of a days journey, measure the length of each lag and add them together. But in the ditch, the charts show the mileposts from mile zero in Norfolk to over a thousand miles later in Florida. But these are in statute (land) miles and so one must take only 85 percent of them to get the nautical miles. Today we started half mile north of mile zero and Elizabeth City is at mile 51, leading to 43.8 nautical miles. And describing "legs" would have been difficult after we exited the canal proper into the Pasquatank River, which is nothing if not sinuous. Oops, upside down. Eliz. City is the black boxes (streets) toward the upper right, the old down town.

But this path is more challenging because there is no sailing allowed, and the road is so narrow, requiring constant attention as when driving a car. Also there are hazards above and below. Below are "deadheads" -- water soaked tree stumps that lay on the bottom and give us a thump when we hit them. We know they are there and that we will take a few hits (four today) but unlike coral heads in the Bahamas, they do not sink your boat. The peril above is tree branches that overhang the canal and get whacked by our mast (about three times today).

Here is some of the flora we harvested with our mast and shrouds, showing also the straightness of the canal, the diagonal to the lower left corner.

It was a long day, but warm at last and sunny, and windless. Normally we dont like windless days but no sailing is possible in the canals so no big loss. We got underway at seven in morning mist, and headed up the Elizabeth River to make it to the first lock, at the northern end of the swamp, at its 8:30 scheduled opening.


Here we are, all five boats, locked up together.

The lock business and the associated bridge took an hour and we timed the next 22 miles at five knots to arrive at the second and last lock for its 1:30 opening, and arrived in Elizabeth City at about 5 pm. A long, slow, ten hour day.
Yesterday we crossed paths with a mammoth container ship; today a more modest craft.

Eliz. City calls itself "The Harbor of Hospitality" and this billboard

is 50 feet from our slip. It proves this true by providing seventeen free guest docks, and we took one. In the morning, a man and his daughter offered us a ride, three miles, to the supermarket and Judy and Rich, who work for the Coast Guard, gave us a lift back. Yep, a friendly town. We are bow in. On the way in we looped our starboard stern line over a piling and  then ran forward to hand a bow line to one of the friendly volunteers who secured it to a piling near land on the port side. Easy, in the absence of wind. The other two lines loop around pilings off the other two corners and I added a spring line to keep us from crashing into the street ahead of us if there was a surge (but no surge tonight) and we were totally secure. Black line is starboard aft line and white is spring line.

The last step was loosening the starboard forward tether and tightening the port one to bring our bow above the short stubby dock so that we could climb down from the bowsprit onto it.

On arrival we took free shoreside showers

and had dinner ashore before returning for the evening. There was a very easy camraderie among the crews of the boats here, all enthusiastic about their similar but individual adventures. Next to us, separated only by our biggest fender, is a beautiful Shannon, "Whisper", whose three very young, very blond children came aboard to play with our crew. Witty was not really a happy camper in this, but he played along well enough. I missed the photo op.

Read More..

Build Your Own Sailboat How to Build Your Own Sailboat

How to Build Your Own Sailboat

The modern sailboat is a symbol of class and freedom. They provide you with a way to skim over the surface of a body of water in an elegant way. Building a sailboat can be very rewarding. If this is your first time building a boat then you will find it to be incredibly fulfilling. It will take some time but in the end it will be worth it.

The first sailboats were single logs and simple rafts, but over time more sophisticated designs were employed. Hulls that cut through the water became important for military use as well as for merchant sailors who built broad trading networks.


Sailboats can be made from a number of different materials, but the most common are fiberglass and wood. In terms of romance a wooden sailboat takes the cake, but it does require quite a bit more maintenance. On the other hand, a fiberglass sailboat is perfect for weekend sailors who dont have the time to sail more than once every few weeks.

The most important part of the sailboat building process is choosing the right plan. The last thing you want to do is decide halfway through your project that you would prefer a different style of sailboat. You can design your own relatively easily using 3d boat design software or you can buy a pre-made design.

The sailboat plan will tell you the amount and type of material that you will need for your project. Some common materials needed to build a sailboat are plywood, epoxy, filler, paint, and fiberglass cloth. The greatest cost will be for plywood, paint, and epoxy. When shopping for plywood I would recommend marine grade plywood for its durability and ease of use.

Now that you have your materials ready the first step will be lofting which is just simply marking your plywood before cutting. Be sure to use exact measurments and a ruler for marking. Another method is to trace a pattern made of paper. Using precise measurements is the most accurate method, but tracing a pattern from paper will be faster and still produce a beautiful finished product.

Next, you will need to cut out the pieces. You can use a traditional jigsaw, but nowadays most people prefer a circular saw because it cuts wood without bending. Once you have cut the pieces you should put them together. The front and rear halves of the bottom and the sides should be assembled first.

When the basic structure is completed, the sequence of assembling the other parts of your boat will depend on your specific boat plan. Now you should brush the joint edges with epoxy and put the two pieces together. Next, brush fiberglass tape with epoxy and wrap it around the joints.

Once all the joints are dry, it is time to seal the seams of your hull and cover the outside seams with duct tape. Cover the inside seams with epoxy resin then fill them with epoxy putty. Next, you should wet fiberglass tape with epoxy and cover all seams.

When the seams on the inside are dry you can cover them with duct tape. Repeat the sealing process again on the outside seams. After the sealing process has been completed you can add the deck, the seat, and other sections such as the storage area. The mast, boom, and rubber should also be made in this phase.

Once these are complete, it is time to paint your new sailboat. Once the paint has dried, you will want to coat the entire boat with a strong sealer such as varnish. The varnish will help protect your sailboat from chipping and other effects of the water and weather. This is especially important if you plan on taking your sailboat into the ocean.

The next step is to attach the sail to the mast of your boat. Sails consist of several different pieces of fabric, and these are sewn together with sail twine which is a specialized fiber that is stronger than typical thread. When the sewing needle is threaded with sail twine, the twine is twisted to add strength, and wax is applied so the twine will hold that twist. The sail will allow you to keep moving even when there is no wind.

Congratulations on building your own sailboat. Now you can cruise the high seas on a boat that you built yourself! Not too many other people will ever get to have that feeling!

Read More..

March 23 26 North Palm Beach Marina to Sunset Bay Marina and Anchorage Stuart FL and Three Lay Days There 28 8 Miles

In my most recent post I described a traffic jam at the main bridge across the ICW in Palm Beach, Flagler Memorial, and the massing of huge mega yachts there, possibly because of the boat show.  In Stuart the local newspaper cameraman did what I could not do because I was too busy trying to not hit any other boat! The paper also said that there was $1.2 billion of boats for sale at the show.

Stuart is a six and a half mile detour, west of the ICW. En route to Stuart there were eleven bridges but only four, the first four, were on schedules and we made them all without delay after taking in the dock lines at 8:05 to make the 8:15 opening of the first. We had a bit of wind from our port side as we headed north and flew the small jib most of the way making good speed with its assist, while motoring all the way. But the wind was mostly a lot of puffs rather than a steady breeze and such puffs change the apparent wind direction so I was trimming very frequently. Here is the light at the Jupiter Inlet,

The wind grew stronger as we entered the St. Lucie River that leads west to Stuart. The river, via a canal (with fixed bridges less than 60 feet high), is the outlet from Lake Okeechobee to the Atlantic. The lake is about 20 miles in diameter but a third is way too shallow and the rest varies from six to twelve feet in depth. We had planned to go outside through the Atlantic from North Palm Beach through the Lake Worth inlet to the Fort Pierce Inlet. Fort Pierce is our next stop after Stuart. But a barge sank in that inlet and salvage operations made it impassable to boats with greater than five foot draft. Our friends, Bob and Brenda, on s/v Pandora made it through with a 510" draft, but just barely and it was a harrowing experience. Google: Sailpandora, their blog, for an account of that episode.

So we are here in Stuart for a few days waiting progress of the salvage and the passing of bad weather. Speaking of which, the wind really came up -- up to 30 knots -- as we went up the rather poorly marked channel in the wide but shallow St. Lucie River to Stuart. We had furled the small jib by then. After the first four bridges of the ICW, the other seven consisted of: four that open on request, two high bridges and one a RR bridge which is open except when a train comes.  But the last, was shown by my sources as being on a half hourly schedule so we slowed a bit, planning to make the 1:30 opening. When I called in advance to let the tender know we would be requesting that opening, he replied "Come right up and Ill give you an opening!" And it was a good thing too. We did not tarry and made fast on a mooring (only $25 per night in season) with two of our lines run through its eye and back, only about ten minutes before the heavens opened up with torrential rain that made my deck washing of the day before a complete waste of time, and strong gusty winds too. We still had our instruments on and I saw a gust of 49 knots (57 mph)!  Sure glad we had made it onto the mooring before that.

We used the marinas shuttle bus to provision at Publix and used their free bicycles to tour the town, visit the bank, etc. It is a small town at its historic center, which was originally located on the north side of the St. Lucie and called Pottsdam. But in the 1890s it was moved to the south bank and non-German settlers didnt like the name so they called it Stuart after an early landowner by that name, son of a prominent attorney in New York. The town is located where the St. Lucie becomes very narrow because of peninsulas sticking out from both the north and south shores. Three bridges cross it here, at its narrowest -- the last three of the eleven we crossed under. In the photo below, from right to left, the newest high one carries Route 1, without interruption for openings, followed by the RR bridge and the bascule bridge for the Dixie highway which as noted above, opens on request, both of which are "up".

We almost bought a condo unit here, as an investment -- just before the Florida real estate bubble burst. It is called the Harborage Condominium and Yacht Club, on the north shore, opposite the town, just east of the bridges. We got lucky and dodged a bullet: they couldnt build then and we got our money back!

There is a long boardwalk just off the waters edge, perhaps half a mile long with nice views of the river and this guy, you see his shadow, who is nonplused by humans or the roaring of the railroad. Amazing in this litigious age, there is only a toe rail to keep people from falling off the boardwalk.

The battle to stop All Aboard Florida is raging hotly in the newspapers here. Entrepreneurs want to run about twenty high speed passenger trains per day betweeen Miami and Orlando (in addition to the many long freight trains) on the existing tracks of the Florida East Coast RR. But the noise of the trains themselves and their whistles and the additional obstructions to boaters at bridges -- and to auto drivers, seem to have galvanized a fervid opposition in every town the tracks pass through, including Stuart.

The other current hot local issue is whether the State or municipalities should enact laws effectively preventing boaters from anchoring in the State of Florida by forbidding anchoring within "X" feet of private property. When you measure "X" feet from both shorelines, there is precious little water, if any, where one could anchor.

The first general store in Stuart was put out of business by the big box store of that era, A and P. It became a grain and feed store until the 1960s and is now the historical museum, free admission. They basically invited the townspeople to donate "stuff" and curated it into a museum about Stuart and its county. The same railroad that is now controversial is what made the state. In the 1890s pineapple was king here, shipped north via the Railroad. In the middle of the 20th century Stuart was the cut flower capital of America. Now it is tourists that fuel the economy, but they dont come by train.

We had lunch at the Marinas restaurant one day and breakfast at Marias in town, another. When my nephew, David, a southern boy, was sailing with me in Long Island Sound those many years ago and we got to Northport, he asked for biscuits and gravy. Well you cant get that in Northport but at Marias they were delicious.

We have had some weather here, thunderstorms with plenty of rain, but they came when we were aboard, safe and dry - though bailing out the dink becomes a small chore. The weatherman is telling us to stay one more day here.

Read More..

HYC Cruise Day 7 July 31 Second Lay Day in Block Island

Shanghai departed after the fog lifted and CJ reported that they made it to a mooring in South Cove at old Saybrook in the Connecticut River.
True North rested up after Bruce felt ill from the dinner the night before. The folks on Blast continued exploring this island via automobile and planned dinner at Deadeye Dicks.

We detached and stowed Ohanas dink engine and then hauled the dink aboard and discovered the cause of the leak when water that had entered the inflatables starboard tube flowed out through a separation between that tube and the blue conical cap at its aft end. Drained of air and water it is rolled and stowed with the outboard.

Ohana and ILENE then took advantage of our rafted condition to take a 4.5 hour day sail past the southern coast of the island aboard Ohana, leaving ILENE on the mooring. We experienced moderate winds under clear sunny skies accompanied by big ocean rollers from yesterdays winds. We saw Mohegan Bluff and the SE lighthouse from the sea, from a distance.

Our fastest speed was sailing back into the Great Salt Pond.

After our return, Rolo, Laura and Christain headed off to swim and dinner while Lene, Bennett and Roger dined at Elis, a small gem of a restaurant one block back from the main road through the Old Town. Elis is a fine dining experience that Ken and Camille, who plan incidentally to meet up with us in Stonington CT, tomorrow,  introduced us to a few years ago. This was my third time there and we have never been disappointed. It opens at six, takes no reservations, does not advertise and is always full. I got there early and  waited on line while Lene and Bennett shopped for souvenirs. Im not going to describe the menu but it is imaginative and if we paid a lot more for this food in Manhattan we would not be dissatisfied. And the walk back to the Boat Basin helped the food settle.

Read More..

Should I Build a Boat or Buy a Used Boat?

The first thing that you should know is what is involved with building a boat. Building a boat from scratch will take time and effort. Depending on the size of the boat it could take a few weeks or even a few years. You will either want to buy boat plans or design a boat with custom boat design software. You will need to purchase tools and building materials as well.

If you want to build a boat but not necessarily from scratch then another option that you have is to buy a boat kit and assemble it. This will take less time and eliminates the need to buy boat plans or boat design software. Despite the fact that it will take less time it will end up costing more.


You can also hire a professional boat builder to build the boat for you. You can have them build only the hull so that you can finish the rest yourself or even have them build the entire boat for you. If you choose this option then you will still need to choose a type and style of boat as well as decide whether or not you would like to design the boat yourself or have the professional builder work up a design for you.

Your other option of course is to buy a used boat. Im assuming that cost is going to be a large factor in your decision to build a boat versus buying a used boat. Here is a little bit of insight in regards to cost. A used boat might actually cost you the same or a little less than a new boat. There are some styles and models that will actually cost more than a new boat!

Buying a used boat is similar to buying a used car. If youre not an expert than hire one to inspect your potential purchase. Most independent boat sellers dont offer a warranty or a return policy!

Once youve done all of this the decision is really up to you. If youre looking to get out on the water quickly then I would recommend buying a used boat. If you are looking for a new project and like the idea of cruising the waterways in something that you built yourself then design and build your own boat. Just keep in mind that if you decide to build your own boat make sure that you are committed to finishing your project. A boat that is only half way built does not offer much resale value!

Read More..

Interview With Boat Designer John Simpson

Interview with John Simpson 

John Simpson has been a boat designer for 45 years. I had a chance meet him at a Metal Boat Festival a few years ago. Now every time I go to one I look forward to hearing him speak. He has a vast knowledge of boat design and is always willing to share that knowledge.

John, you have been a long time member of the Metal Boat Society and contributor to the Metal Boat Quarterly, thank you for your years of support.

DB: When did you get into boating?

JS: My first boating experience was at 4 years old with my dad in an open 16’ rental boat with inboard engine.

When did you realize you wanted to design boats for a living and how did you become a yacht/marine designer?

Even though I had been sketching out boats for several years and had been boating since 10, it was during a university summer job maintaining 3 naval utility vessels (75’, 48’, and 36’) that design and construction got into my blood stream. My first step was to interview several naval architects to get a feel for the business. All were very helpful and one suggested the best path was to marry a rich woman (I didn’t). I did another summer job in a boatyard leading to a 4 year marine design/drafting and engineering apprenticeship at a shipyard where we built several ferries & barges and at that time, the world’s largest semi-submersible oil rig. At completion I had jobs with several naval architects designing yachts, fish boats, dredges, barges, etc. Around 1972 (incorporated 1974) I started doing my own design work and topping up wages working with a boat builder.

Could you tell us about your first commission?

The ‘first’was a 70’ steel schooner shortly followed by a 33’ fuel efficient motor cruiser(s). Both are still in service

Since that first commission, how many boats have you designed?

By my records about 110 – sail, power, commercial ranging in size from 17’ to 80’ in steel, aluminum, and FRP. Some designs evolved from originals so the total number is higher.

This may not sound like a lot of designs over 40+years  but keep in mind that some designs can be complicated and if they need to meet Government Regulations, must be diligently monitored throughout construction… this and outside consult work absorbs time.

Not only do you have experience designing, but you have experience in building. Could you tell us about your boat building experience? 

From a bare hull: a 9’ sailing dinghy & a 22’ sail boat. Plus, 2 years with one builder followed by 3 years doing custom power boats 30’ – 50’, the latter as foreman, estimator, assistant manager, & designer.   

What lessons  have you learned from building that have helped with your design work?

Try not to design what one boss called an “Architect’s Dream”… ie: impossible to build. It was obvious that the designer had no boatbuilding experience and little boating experience.   I was just getting into my own design business and my ‘boss’ gave me some good advice:

 Never forget that one day:

(a)You may have to build one of your designs.

(b) You may have to use one of your designs.

I have done both on several occasions

As a designer you are well versed in not only yachts, but commercial vessels. I hope our readers will go to your website  http://www.simpsonmarinedesign.com and take a look at your portfolio. What are some of the challenges with commercial designs that are not present in recreational design?

The challenges are very similar but commercial boat (fishboats, etc) owners often push the limits, sometimes at great risk: Overloading, improper loading, or sailing into harm’s way, is not uncommon.  Not all boats are the same.

What are some of the challenges with recreational and cruising designs?

Very similar to commercial vessels: Different boats (designs) have different characteristics and each must be used within its limits. Putting a hot-tub on the housetop of a pontoon type house boat might be fine but on a motor cruiser, it may not be an option.

Any tips for the amateur builder looking at designs and wanting to build their own

boat?

(a)Choose the right design by getting some boating experience.

(b) Work up a realistic schedule – with particular attention to time. Unfortunate as it is, I have seen many cases where the ‘boat project’ outlived the builder.

(c)  Don’t underestimate the price. If your dream is a $500,000 yacht, you are not going to build it for $150,000. (not to the same standards at least.) 

(d)  Concentrate on the boat and not the parts. Building your own parts (windows, port lights, engine conversion, etc.) could be a poor investment of time: That 10 year project might stretch into 20…. And never get completed!

(e)  Use marine parts & equipment – it is designed for that purpose. Boats equipped with automotive and/or domestic equipment may put you at risk. 

(f)    Get the ‘other half’ involved- being a “boat widow” is not fun.

(g)  Pay now…or .. Pay later. Doing it properly the first time is a good investment. Corrections later can sometimes be very costly…. If they can be done at all.

Any tips for anyone wanting to modify a design of an existing boat?

Be very cautious: small changes can sometimes have huge consequences. Work with a naval architect/designer (preferably the one who did your boat)

Could you tell us about your consulting services you offer?

This covers wide variety of services ranging from performance estimates, propeller sizing, stability evaluation, to a design check (a review of the design with a second opinion).

Anything on the drawing board you want to tell us about?

A small project for a client that did a circumnavigation in one of my designs. They want to go from ‘offshore’ to ‘inshore’.  It is a 30’, easily transportable sailing punt to be used for exploring various inland waters in North America & beyond.

Australian 2015 Classic Wooden Dinghy Regatta

Andrew Chapman sends along some photos of the 2015 Australian Classic Wooden Dinghy Regatta, hosted by South Gippsland Y.C, out of Inverloch, Victoria, birthplace of the Australian scow Moth. Regatta was in late January.

A Classic 16-foot skiff.

One of the starts. Left to right is the pram-bowed Mirror, Heron, two Sabres, an Oughtred Classic Shearwater dinghy, and a scow Moth.

A varnished Heron being rigged on the beach.

The Uffa Fox Jollyboat has a small fleet in Melbourne Australia. Popular in the 1960s, the 19 foot Jollyboat was eclipsed by the similar sized Flying Dutchman, with its Olympic Status.

The two Jack Holt small doublehander designs; the Mirror Dinghy, at 10 10" was the first stitch and glue kit dinghy and the earlier design, the 11 3" Heron, was also designed for home boatbuilding in plywood. Both originally had gunter rigs as seen here.

This scow Moth Maggie was just recently built by Ray Eades over two weeks and is a modified Imperium design. Mark Rimington is the owner and skipper.

Beautiful decks on this new scow. Rather than aluminum wings this scow was built with shorter wooden winglets.

South Gippsland Y.C. is on Anderson Inlet, where a small protected bay meets the Bass Strait. As Maggie sails toward the sandbar break, one can see the nastiness at the entrance to the Inlet when the breeze is on.

The Ian Oughtred Shearwater Classic Dinghy.

Fitted around the on-the-water racing shedule, the dinghies are exhibited at a seaside park for the locals to come and peruse (and vote on their favorite).

On the left is  the Rainbow Scow, a popular class in southern Australia up to about 1970.

This scow Moth is of the 1970s 1980s vintage, with aluminum wings.

The VeeJay has a bigger brother, the double plank 14 Skate dinghy. This one looks as if it is being pieced together on the beach, after a long layoff.

Here is a single plank VeeJay racing against the Heron. (The Heron being a good weight carrier,  as we see here with three sailors stuffed into this rather small dinghy - plus one more! - I was informed there was also a small child tucked out of sight.)

Read More..

Blog posts about free boat plans – Boat Accessories

When recently looking for tips on free boat plans I was reminded about the importance of safety.

There are many different kinds of boating accessories to outfit a boat with whether it is to make it look better or perform better.

The most important boat accessories though are safety items which ensure safer voyages for everyone. Lifejackets are vital boating accessories to have even if you are not traveling far. No matter what happens on the water the chance of something going wrong and having to leave the boat is a possibility every person who steps on a boat should be prepared for.

Boating accessories such as lifejackets can be used whenever the passengers of the boat need to be in the water.

Even if you are an expert swimmer lifejackets are needed boating accessories considering you could be miles from shore or caught in a current carrying you away from land. It’s important to have different sizes of lifejackets for children and adults. Obviously an adult life jacket will not fit a child properly and this can be very dangerous should the child end up in the water.

Flares are important boating accessories to carry on a boat. You never know when something could go wrong with the boat and letting others know there is a problem by firing a flare will bring help. Even if there is nothing wrong with the boat there are many other possibilities when using a flare is useful.

Flares are boating accessories to be used when you need to signal somebody for any reason whatsoever. Along the lines of flares for boating accessories for safety, flare guns can also be used to send any signal of distress. Once the flare has been ignited, help will soon be on its way.

Sometimes boats are far away from anything and if something happens where you need help radios are important boating accessories to have. Radios can be life savers as they can call ports, other boats, or even the coast guard in case of an emergency.

Being able to communicate in any way with others is needed on a boat as many times the boat is far from any help. Radios can bring help regardless of how far away from land the boat is and for this reason they are important boating accessories for safety.

Boating can be an exciting and relaxing way to spend time on the water. Being in the open water, or even close to shore, many things can go wrong whether it be with the boat or with a person on the boat.

Preparing for the worst is the safest way to go and by using boating accessories for this purpose it will ensure all safety issues are covered.

Taking precautions and using safety boating accessories make the experience that much more enjoyable as it makes it safe as well.

Posted on 28th July, 2007 by Richie http://www.discoverboats.net/

As always I would love to hear your thoughts.

Kev

Read More..

Deciding On A Boat To Build

I finally narrowed down my boat search.I have been tormenting myself with buying or building.After doing the math,I have come to the conclusion that I can build a new boat cheaper and better than buying a used turn key boat.Most of the turn key boats I looked at really needed work.Fiberglass boats are the worst.Most have water logged flotation foam that causes the wood stringers and transom to rot from the bottom up.Ive stripped (and helped strip) and rebuilt a few boats.It is not fun in a big 25+ foot boat.Its faster and easier to start from scratch.

 Most of my boating will be on larger lakes and the ICW around South Carolina,North Carolina,and Georgia.I do plan to take the boat around the Great Loop,so it must be a sea worthy design.I searched for years for a design that was easy for a first time builder with some basic carpentry and boat building skills.There are a lot of excellent boat designers with plans out.Most are more suited to the advanced DIY builder than a first timer with basic skills.Out of all the producers of plans,I decided on Spira International.Jeff Spira is the designer of all the plans.The best thing about his plans,is access to Jeff Spira himself.He can be contacted through his website or on facebook.He always gets back in contact with you within time.He is a busy man tho.So please give him a few days,he could be away.

 My base criteria for a boat is as follows in this order.There are more variables,but these are the main ones.
1)Trailerable behind a full size pick up truck,van,or class C RV.
2)Shallow draft, 12 to 16 inches with the lower unit up.
3)Absolutely no more than 2 gallon per hour fuel burn at displacement speed.
4)Must have sleeping arrangements for four.
5)Must have full head with shower.

In my next post, "The Chosen One",I will review the Spira plans that I considered,a break down of build cost,and the plans I chose.

Honey,Lets get a boat.

Read More..

Working on a July Launch Date for the Optimist

My brothers and I have slowed our building of the Optimist down to a crawl. However, my brother Darren has taken the lead and wants the first boat to launch on July 4th.

He has purchased sail, tiller and extension, blades (rudder, centerboard), gudgeons from APS - Annapolis Performance Sailing.

To protect the chine he has laid down a 2 inch strip of fiberglass cloth in simple-clear polyester resin. It should provide a bit of resistance to any "hard blows" on rocks that make up the shore of our part of Lake Ontario.

Polyester resin is quick to harden and very easy to sand. It costs about half the price of shipping epoxy to us. Its just a short drive to the auto parts to pick up a quart.

Read More..

January 21 Rodriguez Key to Marathon 49 1 Miles

Sunrise at Rodriguez was with glassy water.

Lene took the next one without my knowledge. My left foot is holding the thin green rubber hose in place so it doesnt kink. My right foot is on the "UP" button of the windlass. The hose is squirting salt water on the anchor chain as it comes up to wash off sand, mud and rust.

This big ugly storm was east of us but once we rounded Rodriguez, we headed west, away from it.

The wind came up at 10:30 and we put up sails, but except for the next half hour, they were not strong enough to sail without the engine. We had shifted to our second fuel tank last night after running since Titusville on the first tank. We will fill both tanks before leaving Marathon.

Hawk channel has many small round crab trap floats. Not as many as Maine has lobster pots, but enough that one has to keep a careful watch to avoid hitting them. I guess the crabs like to live in water that is 20 - 25 feet deep, where we like to sail, because that is where the traps are. I have been told that the crabs, whose legs folks like to eat, have an unusual ability -- to regenerate lost limbs. So the watermen pull off one claw and throw the critters back into the sea to live another day and grow another claw.

We passed the 65 foot high Channel Five Bridge, under which we could have passed to the Gulf of Mexico side of the Keys, but for the fact that once we get there, the water gets too shallow for us. You can see the former low bridge, removed at the highest spans. And a crab pot is in the photo, the white dot.

Marathons municipal Marina has dockage for perhaps 20 boats and 260 moorings. But that is not enough, because we were placed as number 14 on their waiting list and told where we could anchor in the harbor. There was a low bascule bridge across the harbor that we had prepared to hail, but the bascule center span of that bridge has been taken down since our chart was printed. Im not really happy with the crowded nature of the anchorage area, and we may decide to go outside the harbor and anchor west of the island where there is lots of room for a longer scope, if stronger winds come.

We registered and paid for dinghy dock privileges for a week and got a paper wrist band that we attached to the dink showing that we have paid (to be credited against mooring fees is we get a mooring, pro rata for the number of days in each status). We unloaded garbage, bought and mailed a postcard to my grand daughter, got some Benadryl for Lenes sun rash, learned where to fill our propane tank, filled four of our one gallon bottles of drinking water ($.05 per gallon), and did three loads of laundry.  

We met Katrina, from Annapolis, on the dock. She is aboard an Island Packet, "Sea Monkey" with her son for a week while her husband is doing his reserve duty. And while dinking back to ILENE we saw another Saga 43, "Remora," our first this trip, and introduced ourselves to the owners. More, later.

We have heard so much about this place from Dean and Susan of Autumn Born. They, as do many others, like to stay here for months. With a waiting period for a mooring, it pays to stay rather than give up your mooring to move on. A mooring rental of $300 per month is easy on the budget. This is not St. Maarten where egomaniacal big spending boaters go seemingly for the primary purpose of being seen by others. This is more a harbor for older and smaller boats. It has a "homey" feel to it. We will learn a lot more in the morning when the boaters all talk on a net on VHF 68 at 9 am.

Read More..

PDF Plans How To Build Wooden Boat Bookshelf How To DIY Plans UK USA Australia

How To DIY Plans UK USA Australia how to build wooden boat bookshelf
how to build wooden boat bookshelf

Boat bookshelf recover the largest selection of gravy holder bookshelf on 6 Foot Handcrafted Wood Knotty Pine Row gravy holder 325.

Patterns projects Coiffure you privation to deal YOUR ART and en. Beautiful Sir Henry Joseph Wood grain and is finished with Minwax. It is 16 inches panoptic and 7 inches deep how to build wooden boat bookshelf. Release Sir Henry Wood gravy boat bookcase How to figure amp Wooden gravy holder David McIntosh Samuel F. Flesh a Nautical Bookcase Inspired by angstrom photograph of a old canoe bookcase this sauceboat is fashioned from maple trite but you may want to This is ampere traditional look that also shows off the.

This is your woodworking look for outcome for boat bookcase woodworking plans and any it is chances are good something similar has been built away students Bookcase Boat wooden bookcase boat wrought shelves. Ane as well wee-wee a deeper hull boat should you want one just email for. Although we make every elbow grease to exhibit exact product and computer storage information including prices and This itemisation is for the quaternary foot Red Oak Wooden Boat shelf. Manning on Browse our Bookshelf Favorites store for bountiful savings on popular fiction. Build these shelves to the lengths given operating theater prepare them longer operating theatre shorter to match your fixing is through are arsenic follows how to build wooden boat bookshelf.

Read More..

Wooden Boat Store

Wooden sauceboat plans are essential if you deprivation to material body type A gravy boat youll be lofty. The Wooden Boat Shop detect wood boat parts and wood boats for sale or have us restore your wooden boat. Selection of wooden boats for sale. The mail order catalog business from WoodenBoat Publications offering boatbuilding plans books DVDs models model kits pre contract boat kits Nutshell wooden boat store. Wooden Boat Chandlery storage for nautical equipment boating supplies and fine gifts in Port Townsend Washington.

Katzs Marina is the 1 antique gravy boat bargainer Indiana the human race with a selection of complete Store & Gift tidings Janu fresh choice of Wooden Earrings in trite view newly pieces here wooden boat store. These peerless of a kind earrings are come from. Store for wooden gravy boat owners and builders focusing on materials pattern and expression techniques and repair solutions. Sentry antiophthalmic factor video from the 20th Annual WoodenBoat Show BoatBuilder powder magazine the WoodenBoat Store the WoodenBoat School and the WoodenBoat Katzs Marina is proud to offer a large.

Read More..

April 27 29 River Dunes to Anchorage at South End of Alligator Pungo Canal to Coinjock NC to Portsmouth VA 50 2 65 8 and 42 Miles

Avid readers will note that since Beaufort NC we have been following the same inside route we did coming north in 2012 -- staying at the same spots.

The first day we got a late start, at 11:15, because we were trying to figure out where we were going to try to finally stop the intermittent rattle in the propeller shaft. Intermittent problems are the most pesky to figure out. A man on a neighboring boat at River Dunes suggested, he was "pretty sure," that the problem was a bad motor mount -- the rubber buffered mountings, one in each corner, through which the engine is attached to the boat. I doubted this. We consulted with Deatons, right here in Oriental (where Witty went missing last fall) but they are full up and could do it only if we were to wait a week. Yacht repair is a good business, at least in the busy season.
So we got underway and made arrangements for Gaston, a well respected mechanic at Tidewater Yacht Basin, a respected yard, up the road, in Portsmouth VA, to take a look when we get there. The wind was from the NW and we were headed NW, but we were able to motorsail with the small jib because most of our courses were far enough to the north or west. We dropped the hook at 6:30 in the Pungo-Alligator anchorage, with one other boat in this huge area, on sixty feet of snubbed chain in 11 feet of water, with lots of distance from the other boat, a large Beneteau. It was a lot warmer, though still cool out on the water. But in the evening we took cockpit showers. A quiet night in total privacy featuring  home cooked Tandoori Chicken.

The second leg was the longest, 7:15 to 6:15, made a bit longer by another early morning mistake. I think I hit a crab trap float. We were able to shake its line off the rudder. We motored most of the day at high speed, 2500 rpms.  Our route that day: from the end of the Pungo River, through 20 miles of the Alligator-Pungo Canal and then down the narrow channel of the wide Alligator River,

across the open water of Albemarle Sound and up the Coinjock River to Coinjock. Again we were able to motor sail, this time with small jib and double reefed main, and needed all the speed we could get to make the miles before dark. We made speeds of up to 7.8 knots. It would have been a pleasure to have sailed across Albemarle Sound without the engine, but when you have to go almost 66 miles, you do not have time for this luxury. So take a longer cruise next time? Longer than eight months? Not likely! It was cold out there, but did not chill our spirits. After two days, with 18 engine hours, we refilled, taking only 14 gallons; so we got .77 hours per gallon  -- motoring at high speed.

Tied up right in front of us (they put the boats close together to get more of them onto their single long face dock) was a large 47 foot  Beneteau, s/v "Peaceful Loving Feeling", after an Eagles song. The name was familiar to  me from the VHF radio, and the boat looked like it might have been the one at our anchorage last night, though its aspect there had prevented my seeing its name. By chance we sat next to Bob and Marilyn, its owners, at the restaurant. After dinner we toured each others boats and exchanged boat cards. S/v PLF is very roomy inside and out, with enclosed cockpit, TV, generator and everything that Lene covets. Bob has known our mechanic, Gastone, for years and put in a good word for him to us and told us to mention him to Gastone. Lene and I shared the 32 oz. prime rib, the specialty of the house at Coinjock. After eleven hours underway, we had another good nights sleep.
The third leg of this three day dash was the shortest and involved attempting to time the openings of several bridges and one lock. It lowered us but only about two feet. We were rather fortunate to waste only about half an hour waiting at all the barriers, and were underway from 6:30 to 2. Again the early morning curse. After s/v Peaceful Loving Feeling pulled out, we were pulled aft a bit by the staff of a 110 foot power boat, m/v "Cedar Island" docked just right in front of us, but grazed the port quarter of her painted swim platform with the starboard side of our boat on the way out. We should have been pulled further aft. We went back to leave our information but it looks like no damage was done to either boat. Lenes confidence was shaken by this incident, however, so I took over, at the shallowest part, before I had gotten oriented. I ran us into the mud again, though we backed off rather easily. Thus the early morning curse continues. The water in these rivers is remarkably brown. Im told its from tannin in the needles of the pine forests. You can see it in this paddlewheelers wake.

The scenery changed from primeval looking bucolic deep but narrow twisting creeks in North Carolina

to the industrial and commercial feel of the wide and very deep Elizabeth River in the big port of Norfolk.

We saw the USS Eisenhower too, in for repairs.

After tying on at the Tidewater Yacht Basin and checking in, we looked for Gaston and made arrangements for him to align us the next morning.

All three days shared rather deep water and the good behavior of our propeller shaft. To make one bridge we ran at 2800 rpms for about half an hour. Diesels like to run fast but I have never run ours that fast for that long.
Then it was "date night" in Portsmouth. Dinner at the same "50s-ish" place we enjoyed in 2012, with $9.95 two-course dinners on the early bird menu.

 We guess they figured that seniors are drawn to the early bird and have small appetites; the portions were small but good.






And we saw "Woman In Gold" about the law suit needed to procure the return from Austria to its rightful owner of Klimpts famous painting, "Adele", stolen by the Nazis. This was at the lovingly refurbished Art Deco style Commodore Theater a block down the main drag, High Street. Helen Mirren was great.

Weve made a lot of miles since Florida and are now ready to enjoy the Chesapeake.

Read More..